Huawei S7703 Switch
Supports dual MCU(Main Control Unit)
Supports 3 service slots LPU(Line Processing Unit)
Supports 1+1 AC/DC power redundancy
The S7700 series switches (S7700 for short) are high-end smart routing switches designed for nextgenerationenterprise networks. The S7700 design is based on Huawei's intelligent multi-layer switching technology to provide intelligent service optimization methods, such as MPLS VPN, traffic analysis, comprehensive H-QoS policies, controllable multicast, load balancing, and security, in addition to high-performanceLayer 2 to Layer 4 switching services.
|Packet forwarding rate||15.36/40.00Tbps|
|Maximum port density|
V100R006C00 version: 144×FE,144×GE,36×10GE
V200R001C00 version: 144×FE,144×GE,120×10GE
V200R010C00 or later version:144×FE,144×GE,144×10GE,24×40GE,12×100GE
|AP access control, AP region management, and AP profile management|
Radio profile management, uniform static configuration, and centralized
|Basic WLAN services, QoS, security, and user management|
|Deployment of ACs on different network layers|
|User management||Unified user management|
|802.1x, MAC address, and Portal authentication|
|Traffic- and time-based accounting|
|User authorization based on user groups, domains, and time ranges|
|VLAN||Three types of interfaces: access, trunk, and hybrid|
|QinQ and selective QinQ|
|MAC address-based VLAN assignment|
|MAC address||MAC address learning and aging.|
|Static, dynamic, and blackhole MAC address entries|
|Packet filtering based on source MAC addresses|
|Limit on the number of MAC addresses learned on ports and VLANs|
|Ring Protection||STP(IEEE 802.1d), RSTP(IEEE 802.1w), and MSTP(IEEE 802.1s)|
|BPDU protection, root protection, and loop protection|
|IP routing||IPv4 routing protocols, such as RIPv1/v2, OSPF, BGP, and IS-IS|
|IPv6 dynamic routing protocols, such as RIPng, OSPFv3, ISISv6, and BGP4+|
|Multicast||IGMPv1/v2/v3 and IGMP v1/v2/v3 snooping|
|PIM-DM, PIM-SM, and PIM-SSM|
|MSDP and MBGP|
|Multicast traffic control|
|Multicast packet suppression|
|MPLS||Basic MPLS functions|
|Reliability||LACP and E-Trunk between devices|
|VRRP and BFD for VRRP|
|BFD for BGP/IS-IS/OSPF/static route|
|NSF and GR for BGP/IS-IS/OSPF/LDP|
|TE FRR and IP FRR|
Traffic classification based on Layer 2 protocol packet header, Layer 3 protocol
information, Layer 4 protocol information, and 802.1p priority
|ACL, CAR, re-mark, and scheduling|
|Queue scheduling algorithms including SP, WRR, DRR, SP+WRR, and SP+DRR|
|Congestion avoidance mechanisms, such as WRED and tail drop|
Security and management
|802.1x authentication and portal authentication|
|RADIUS and HWTACACS authentication|
Different user levels for commands, preventing unauthorized users from using
Defense against DoS attacks, TCP SYN Flood attacks, UDP Flood attacks,
broadcast storms, and heavy traffic attack
|Ping and traceroute|
|Interoperability||Supports VBST (Compatible with PVST/PVST+/RPVST)|
|Supports LNP (Similar to DTP)|
|Supports VCMP (Similar to VTP)|
|Power supply||AC:90 V to 290 V|
442 mm x 476 mm x 175 mm
consumption of the entire
|Maximum PoE power||2200 W|
Q: How are slots of an S7703 chassis distributed?
Q: What's the difference among S7703, S7706, S7710, S7712
|Switch Capacity||15.36/40.00Tbps||16.00/76.80Tbps||57.92/256.00T Tbps||21.76/107.52Tbps|
|Packet Forwarding Rate||1440/14400Mpps||2880/21120Mpps||8400/69120Mpps||2880/41280Mpps|
|Main Control Slot||2|
Q: What are the types of the Main Control Boards of the S7700 and S9700?
The main control boards of the S7700 include ES0D00MCUA00, ES0D00SRUA00, ES0D00SRUB00,and ES1D2SRUH000. The details are as follows:
The ES0D00MCUA00 is installed on the S7703.
The ES0D00SRUA00, ES0D00SRUB00 and ES1D2SRUH000 are installed on the S7706 and S7712.
The main control boards of the S9700 include EH1D2MCUAC00, EH1D2SRUDC00, EH1D2SRUDC01, and EH1D2SRUC000. The details are as follows:
The EH1D2MCUAC00 is installed on the S9703.
The EH1D2SRUDC00, EH1D2SRUDC01 and EH1D2SRUC000 are installed on the S9706 and S9712.
Q: Are the Main Control Boards and LPUs hot swappable?
A: All the main control boards and LPUs of the S7700&S9700 are hot swappable. In addition, the fans and power supplies are hot swappable.
The ES0D00FSUA00, ES02VSTSA, EH1D2VS08000 and ES1D2VS04000 are not hot swappable.
Q: Does the S7700 and S9700 support hot backup?
A: The S7700&S9700 supports hot backup. When the master main control board fails, the S7700&S9700 automatically switches services to the slave board without interrupting the services. The software versions of the master board and slave board must be the same.
Q: Does the S7700 and S9700 support the optical modules of other vendors?
A: Use optical modules certified for Huawei switches. Non-certified optical modules cannot ensure transmission reliability and may affect service stability on the switch. We will not responsible for any problem caused by non-certified optical modules and will not fix such problems.
Q: Does the GE optical LPU of the S7700 and S9700 support 100M optical module?
A: Yes, the S7700&S9700's GE optical LPU supports both 100M optical modules and 1000M optical modules.
When a 100M optical module is used, you must run the speed 100 command on the interface to set the interface rate to 100 Mbit/s.
When using a GE optical module, an interface works at 1000 Mbit/s by default. If auto-negotiation is enabled on the interface, the interface speed cannot be set to 100 Mbit/s. If auto-negotiation is disabled, you can run the speed 100 command to set the interface speed to 100 Mbit/s.The 100M optical interface can only use the 100M optical module, and the default interface rate is 100M.
When two optical interfaces are interconnected, they must use the same type of optical module.
Q: Does the S7700 and S9700 support the AC power supply and DC power supply?
A: AC and DC power modules or power modules of different power values cannot be installed simultaneously in the same type of power slots (system or PoE). In versions earlier than V200R006C00, the PoE slots of a switch allow only AC power modules. To use the PoE function on a switch, use AC power modules as the system power modules. In V200R006C00 and later versions, the PoE slots allow both AC and DC power modules.
Q: Are the power modules of S7700 and S9700 hot swappable?
A: Power modules of the S7700&S9700 are hot swappable. Before removing a power module, ensure that the chassis can work normally without the power module. When removing or installing a power module, take electrical protective measures to avoid electric shock.
Q: What are the functions of the CF card of the S7700 and S9700?
A: The S7700&S9700 series switches support standard CF cards. The default capacity of a CF card is 512 MB, expandable to 1 GB or 2 GB. The CF card is used to store system files, configuration files, paf, License, and log files.
The S7700&S9700 series switches can start by using the startup file in the CF card. In this case, the system software package is stored on the CF card. It is required to specify the system software package on the CF card as the boot file. On the S7700&S9700 series switches, logs can be stored on the CF cards.
Q: Is the CF card hot swappable?
A: The CF cards are not hot swappable.
Q: Can GE optical modules and GE electrical modules be installed on the same interface board of the S7700 and S9700?
A: GE optical modules and GE electrical modules can be installed on the same 1000M optical interface board of the S7700&S9700, but you must configure the O/E converter on the 1000M optical interface board.
The 1000M optical interface board of the S7700&S9700 can use only the Huawei certified converter. When O/E converters of other vendors are installed on interfaces of the S7700&S9700, the interfaces still work as optical interfaces.
Q: What are the differences between the E series, F series, and S series LPUs of the S7700 and S9700?
A: S7700&S9700 LPUs are classified into three series: E series, F series, and S series.
The E series is the enhanced series, and supports Multiprotocol Label Switching (MPLS) and extension of routing, ACL, and MAC address entries. The E series consists of the EA, EC, ED, and EE LPUs.
The F series is the ordinary series, and supports MPLS but not extension of MAC address entries. The F series consists of the FA and FC LPUs.
The S series is the standard series and does not support extension of MAC address entries. The S series consists of the SA and SC LPUs. The SA LPUs do not support MPLS, whereas the SC LPUs support MPLS.
Q: Can I get technical support from Thunder-link.com if we purchase LS-S7703 from you?
A: Yes, Thunder-link.com has experienced technical team on Huawei switches, however, you may need to purchase technical support service from us as by default we only provide one year hardware warranty.
Q: Can traffic be mirrored to an interfance on S7700 series switch?
A: Currently traffic mirroring can be configured for both inbound and outbound traffic. Traffic, however, must be mirrored to an observing interface.
Q: Does the S7700 series switch support inter-board mirroring?
A: Yes, the S7700 supports.
This function has a bug: If an outgoing packet on the mirrored interface is untagged, a tag is added to the packet when the packet is sent out through the observing port.
Q: Does S7700 series switch support netstream?
A: The V100R003 and later versions support NetStream.
Q: Does S7700 series switch support IGMPv3?
A: The S7700 series switches support only a simplified version of IGMPv3 in Layer 2 multicast application. In this version, either (*, G) entries or (S, G) entries will be generated for a multicast group. If (*, G) entries are generated, data of all sources is received. If (S, G) entries are generated, data of a specific source is received. If the specified group address is in the SSM group address range, only source-specific programs can be ordered.
Q: Does S7700 series switches support static RP?
A: On S7700 series switches, you can configure a maximum of 50 static RPs by running the static-rp command repeatedly in the public network instance PIM view or VPN instance PIM view. An ACL can be referenced by only one static RP. If no ACL is specified in the static-rp command, only one static RP can be created.
Q: Does S7700 series switches support static multicast routes?
A: The S7700 series switches support the igmp static-group command to configure static groups. In addition, they support static multicast routes configured through the ip rpf-route-static command.
Q: Does S7700 support the weighted load balancing mode?
A: The S7700 perform load balancing among equal-cost routes, but does not perform load balancing based on weights.
|Thunder-link.com have regular products in stock, and work together with reliable and high efficiency shipment partner, could deliver to our customers worldwide shortly. In normal condition, your cargo would take 3-5 days lead time and inland transportation to your carriers, then takes delivery days as per different delivery method, would be arrived at your destination safely and securely through reliable international carriers. Tracking No. will be provided once delivery out.|
|There are 3 delivery methods as default selection.|
|· FCA China Mainland.|
|Free of charge for FCA China Mainland|
|· FCA Hong Kong.|
|Flat rate 150USD for cargo under 100KG. We can delivery to your appointed address in Hong Kong, like your forwarders address.|
|Please note: |
1, Our warehouses and cargoes are not located in Hong Kong, there are logistic and customs commission charges during China to Hong Kong.
2, If your cargo is small dimension, instead of delivery to you Hong Kong carrier, choosing our DHL service to deliver to your country directly is highly recommended.
|International shipping methods are by express like DHL/ Fedex/ UPS, DHL is default; or by normal airfreight; |
For cargoes under 45kg, DHL is recommended; For cargoes more than 45kg, considering the time-effectiveness, customs clearance convenience, and freight cost, our sales team will provide DHL and normal airfreight cost for your choice.
1, Insurance is not included by default, please tell our sales team if you need a insurance during transportation.2, DHL is door to door service, if you choose normal airfreight, you should collect the cargo at airport; and if there have no airport at your city, you should also responsible for the inland transportation between airport to your place.
|Thunder-link.com accepts variety payment methods. We will constantly upgrade our payment system and provide the most convenient method for our client. The Customer may make payment by any one of the following methods, and Wire Transfer is the regular method in Thunder-link.com.|
|Paying with Wire Transfer|
|You can do from any your local bank. Usually, we will have your payment within 2 to 3 day.|
|All fee (payer & payee) generated by the bank wire transfer should be bear by client. Otherwise, the fee will be deducted from the payment we receive.|
|Paying with Paypal|
|Thunder-link.com offers an alternative secure payment method via PayPal. PayPal does not insist you open an account, making payment by Credit or Debit card even easier. It's advised you do create an account to enable the benefits of signing up with PayPal, such as buyer protection and faster checkout next time without the need to enter your card details. Our invoicing and back order systems with PayPal work differently from our other payment methods. Our returns system is slightly different, we can only refund you for the items rather than swap them. When paying through PayPal the total order amount will be paid for immediately at checkout when you commit to buy. The items will then be dispatched when we process the order as quickly as we can. If items are out of stock we will aim to dispatch them as soon as possible after they arrive here. The same applies for any back orders that are created due to out of stock items within a larger order. Any canceled orders will be refunded as quickly as possible. Any returns will always be charged back to your original payment method.|
|Paying with Western Union|
|When you buy some items in Thunder-link.com, you have the option of paying for them at any participating Western Union location. The Western Union charge that applies to Thunder-link.com is based on the total amount of your transaction.|
|All fee (payer & payee) generated by the bank wire transfer should be paid by client.Otherwise, the fee will be deducted from the payment we receive.|
Paying with Alipay
|Now Alipay is acceptable at Thunder-link.com, if you have and intend to pay by an Alipay account, please contact with our sales team.|
|Please send us the T/T payment advice with date and invoice number by using below email or telephone number.|
|Email to: [email protected] Call to : +852-3062-3083|
|All products are vender original products, we provide new equipment for customers, never been used before. Some scratching or copper rust might be seen on the modules, that may caused by carry, inserting in/out from chassis during our in-stock and pre-delivery testing. In normal condition, the scratching and rust are very slightly. When meet with this situation, a picture will send to you first to obtain your confirmation before delivery to you.|
|Once you bought products from us, we will provide the best post sale service for you. After the shipping out, we will continuously track your cargo until it arrives to your country or region. If there is something wrong during the delivery, we will do our utmost to help you.|
|Generally, all products provided by Thunder-link.com, will come with standard vender like 1 year warranty. During the warranty period, Thunder-link.com will replace any defective Equipment, but the reverse logistics should responsible by buyer, the re-shipment should obey the trade terms of order. If it is unable to locate a suitable replacement, Thunder-link.com will repair the Equipment. If it is unable to do either, Thunder-link.com will refund the purchase price to Buyer.|
|This warranty does not apply to any failure of the Equipment as a result of misuse, abuse, accident, neglect or mishandling, lack of proper maintenance, environmental factors, improper installation or configuration, flood, fire or other natural disasters, physical damage, electrical issues such as lightning, power surges or incorrect electrical voltages, or improper modifications.|
|This warranty is only valid for the original purchaser of the Equipment (“Buyer”).|
But if products fail during warranty time, please contact your sales representative, or email to [email protected] to verify your problem and enquire solutions for the failed products. If the problem still can't be fixed by remote support trouble shooting methods i.e. email or phone support, then return procedure triggered.
|See details when you start the return procedure to return policy.|
|If there’s any post sale question please e-mail at [email protected] or contact with your sales representative.|