8x1000BASE-T POE+ 4xGE SFP 2x1000BASE-T combo 1xAC power fixed
3-Level Quality Control x
We provide 3-Level Quality Control procedure: 1-Level inspection; 2-Level In-stock test; 3-Level 24 hour pre-delivery and 1 year warranty. Learn More
8-Year Gold Supplier x
Thunder-link.com, founded in 2011, a leading professional Huawei network hardware and solution provider, service over 100 VIP customers from 50 countries in 8 year. Learn More
Huawei S5720-12TP-PWR-LI-AC switch with 8-ports 1000BASE-T POE+, 4-ports GE SFP, 2-ports 1000BASE-T combo
With 1 AC power fixed
No extension slots
Forwarding perfomance: 27Mpps
Switching capacity: 336Gbps
16K MAC address entries
Huawei Quidway S5720-LI series is a next-generation, energy-saving gigabit Ethernet switch that provides flexible GE access ports and 10 GE uplink ports. Building on next-generation, high-performance hardware and the Huawei Versatile Routing Platform (VRP), the S5720-LI supports intelligent stack (iStack), flexible Ethernet networking, and diversified security control. It provides customers with a green, easy-to-manage, easy-to-expand, and cost-effective gigabit to the desktop solution.
|Fixed port||8 x Ethernet 10/100/1,000 Base-T ports, 4 x Gig SFP ports, 2 x combo 10/100/1,000 Base-T Ethernet ports|
|MAC address table||STP (IEEE 802.1d), RSTP (IEEE 802.1w), and MSTP (IEEE 802.1s)|
|16K MAC address entries|
|MAC address learning and aging|
|Static, dynamic, and blackhole MAC address entries|
|Packet filtering based on source MAC addresses|
|Guest VLAN and voice VLAN, GVRP, MUX VLAN|
|VLAN assignment based on MAC addresses, protocols, IP subnets, policies, and ports|
|1:1 and N:1 VLAN Mapping|
|Reliability||RRPP ring topology and RRPP multi-instance|
|Smart Link tree topology and Smart Link multi-instance, providing the millisecond-level protection switchover|
|ERPS(G.8032）(supported by the S5700-LI/S5700-SI/S5700-EI/S5700-HI series)|
|STP, RSTP, and MSTP|
|BPDU protection, root protection, and loop protection|
|IP routing||Static route, RIP, RIPng, and OSPF|
|IPv6 features||Neighbor Discovery (ND)|
|Path MTU (PMTU)|
|IPv6 ping, IPv6 tracert, and IPv6 Telnet|
|ACLs based on the source IPv6 address, destination IPv6 address, Layer 4 ports, or protocol type|
|MLD v1/v2 snooping|
|Multicast||IGMP v1/v2/v3 snooping and IGMP fast leave|
|Multicast forwarding in a VLAN and multicast replication between VLANs|
|Multicast load balancing among member ports of a trunk|
|Port-based multicast traffic statistics|
|QoS/ACL||Rate limiting on packets sent and received by an interface|
|Port-based traffic policing and two-rate three-color CAR|
|Eight queues on each port|
|WRR, DRR, SP, WRR+SP, and DRR+SP queue scheduling algorithms|
|Re-marking of the 802.1p priority and DSCP priority|
|Packet filtering at Layers 2 through 4, filtering out invalid frames based on the source MAC address, destination MAC address, source IP address, destination IP address, port number, protocol type, and VLAN ID|
|Rate limiting in each queue and traffic shaping on ports|
|Security||User privilege management and password protection|
|DoS attack defense, ARP attack defense, and ICMP attack defense|
|Binding of the IP address, MAC address, interface, and VLAN|
|Port isolation, port security, and sticky MAC|
|Blackhole MAC address entries|
|Limit on the number of learned MAC addresses|
|802.1x authentication and limit on the number of users on an interface|
|AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC|
|Hypertext Transfer Protocol Secure (HTTPS)|
|Blacklist and whitelist|
|Access Security||DHCP relay, DHCP server, DHCP snooping, and DHCP security, DHCPv6 relay, DHCPv6 server, and DHCPv6 snooping|
Super Virtual Fabric (SVF)
|Working as an SVF client that is plug-and-play with zero configuration|
Automatically loading the system software package and patches of clients One-click and automatic delivery of service configurations
|Supports independent running client|
|Management and maintenance||iStack(excluding S5700-10P-LI-AC, S5700-10P-PWR-LI-AC, S5700S-28P-LI-AC, S5700S-52P-LI-AC and battery LAN switches)|
|Virtual Cable Test (VCT)|
|Remote configuration and maintenance using Telnet|
|eSight and web-based NMS|
|System logs and multi-level alarms|
|Dying Gasp (excluding battery LAN switches)|
|Operating temperature||0°C to 45°C|
5% to 95% (non-condensing)
Rated voltage range: 100 V to 240 V AC, 50/60 Hz
Maximum voltage range: 90 V to 264 V AC, 47/63 Hz
|Power consumption||without PD: 15.61W; with PD: 160.5W (PoE: 123.2W)|
Dimensions(W x D x H)
|320mm x 220mm x 43.6mm|
Q: Does S5720-12TP-PWR-LI-AC support stack?
A: Yes, but it is not through the stack card, it is through the GE uplink interface.
V200R001: The last two uplink 1000Base-X optical ports can be used as stack ports.
V200R002 and later versions: The four uplink 1000Base-X optical ports can be used as stack ports.
Q: What is the difference between Huawei S5700 switch and 5300 switch?
A: Huawei S5700 target the enterprise market, S5300 target at telecom market, but most function are the same, the manufacturer did this mostly for marketing reasons as the telecom market most are big customers with better discount.
Q: Can an Electrical Interface of the S5700 be connected to an O/E converter?
A: An optical interface of the S5700 can be connected to an O/E converter.
Q: Does the S5700 Interface Support 100M Optical Modules?
A: Fixed optical interfaces on the S5700-EI, S5700-SI, S5710-LI, and S5700-HI support 100M optical modules, while interfaces on extended front cards do not support 100M optical modules.
Combo optical interfaces and 100/1000Base-X optical interfaces on the S5700-LI and S5700S-LI series switches support 100M optical modules.
The S5710-EI series switches support 100M optical modules only on their combo optical interfaces.
Combo optical interfaces and 100/1000Base-X optical interfaces on the S5720-EI series switches support 100M optical modules.
In the S5720-HI series, only the S5720-32C-HI-24S-AC supports 100M optical modules on their 100/1000Base-X optical interfaces.
The S5720-SI series switches support 100M optical modules only on their combo optical interfaces.
Q: How Do I Know that the S5700's Fan Operates Normally in Intelligent Mode?
A: The fans can work in the intelligent mode or forcible mode.
In the intelligent mode, the fans start to operate only when the ambient temperature goes higher than a specified value. In V200R003C00 and later versions, you can run the display fan speed-adjust threshold minus command on the switches that use the intelligent heat dissipation mode to view the temperature thresholds for the fans to start and stop running. The set fan speed-adjust threshold minus command can be used to lower these temperature thresholds.
Intelligent heat dissipation：
Q: Does the S5700 support LRM optical modules?
A: The S5700SI supports long reach multimode (LRM) optical modules since V100R006C00SPC800. The S5700EI supports LRM optical modules since V100R006C01.
The S5700-LI (10GE optical ports), S5710-C-LI (10GE optical ports), S5700-HI (10GE optical ports), S5710-EI (10GE optical ports), and S5720-EI (only 10GE optical ports on extended interface cards) support LRM optical modules.
Q: Do 10GE Front Subcards of S5700 Switches Support GE/10GE Auto-Sensing?
A: The 10GE front subcards of the S5700EI do not support GE/10G auto-sensing, and 10GE front subcards of the S5700HI and S5700SI support GE/10G auto-sensing.
Q: Can 4*GE and 4*10GE Front Subcards of the S5700EI and S5700SI Switches Be Used Without an Extended Rear Subcard?
A: When a 4*GE or 4*10GE front subcard is used without an extended rear subcard, only two of the four ports on the subcard can be used:
• 4*GE subcard: Only the first and second ports can be initialized. The ports are displayed as GigabitEthernet */1/1 and GigabitEthernet */1/2 after initialization.
• 4*10GE subcard: Only the first and third ports can be initialized. The ports are displayed as XGigabitEthernet */1/1 and XGigabitEthernet */1/2 after initialization.
Q: Are the Cards of S5700 Hot Swappable?
A: Interface cards on the S5700 series except for the S5700EI and S5700SI are hot swappable.
Q: Why Only Two Optical Interfaces Are Displayed After a Front Card Is Installed on an S5700?
A: The reason is that no extended rear card is installed on the S5700.
An S5700-EI or S5700-SI can provide only two optical interfaces for a front card. If a 4-port front card is installed, an ETPB extended rear card must be installed to provide the other two ports. Otherwise, only two optical interfaces are displayed.
Q: Can the Front Card and Stack Card of the S5700C Be Used Simultaneously?
A: When a 2-port front card is installed, the front card and the stack card can be used simultaneously.
If a 4-port front card (ES5D000X4S01, ES5D00G4SA01, or ES5D000G4S01) is installed, an ES5D00ETPB00 extended rear card must be installed.
Q: Are Subcards of the S5700SI and S5700EI Support 10GE Ports?
A: The S5700SI and S5700EI switches use front subcards to provide 10GE ports. The ES5D000X2S00 and ES5D000X4S01 front subcards provide 10GE ports on the S5700SI and S5700EI switches. They use SFP+ optical modules.
The S5700SI and S5700EI switches support the ES5D000X2S00 and ES5D000X4S01 front subcards since V100R005.
• An ES5D000X2S00 front subcard can be used without a rear subcard or together with a rear subcard supported by the switches.
• When an ES5D000X4S01 front subcard is used together with an ES5D00ETPB00 extended rear subcard of which the PCB version is VER.C, all the four ports on the ES5D000X4S01 front subcard can be used. If an ES5D000X4S01 front subcard is used without an ES5D00ETPB00 extended rear subcard or used together with a stack rear subcard, only the first and third ports on the front subcard can be used. The two ports are displayed as XGigabitEthernet */1/1 and XGigabitEthernet */1/2 in command lines.
Q: SW5700 Can GE Optical Ports Use 10GE Optical Modules?
A: The four uplink GE optical ports of the S5720-P-SI and S5720S-P-SI series can use 10GE optical modules, but can only be used for stack connections in this case. GE optical ports of other switch models cannot use 10GE optical modules. 100M optical ports cannot use GE or 10GE optical modules.