![Icon [all products]](https://www.thunder-link.com/tl-content/uploads/2022/05/Icon-all-products-1.svg "Icon [all products]"){kind=icon}
All products
| Item | Specification |
| Installation Type | Wall |
| Ceiling | |
| T-Rail | |
| Dimensions without packaging (H x W x D) [mm(in.)] | Diameter x length: 220 mm x 53 mm (8.66 in. x 2.09 in.) |
| Dimensions with packaging (H x W x D) [mm(in.)] | 93 mm x 284 mm x 251 mm (3.66 in. x 11.18 in. x 9.88 in.) |
| Weight without packaging [kg(lb)] | 1.22 kg (2.69 lb) |
| Weight with packaging [kg(lb)] | 1.76 kg (3.88 lb) |
| Storage | NAND Flash 512 MB |
| Console port | BLE console |
| Maximum power consumption [W] | 22.6 (excluding USB) |
| Maximum heat dissipation [BTU/hour] | 77.1 (without USB) |
| Power supply mode | DC adapter |
| PoE | |
| Rated input voltage [V] | 12 V |
| Input voltage range [V] | DC: 42.5 V to 57 V |
| PoE: 802.3at/af | |
| Service port surge protection [kV] | PoE port: |
| Differential mode (48 V-RTN): 0.5 kV (1.2/50 us, 42 ohms), criterion B | |
| Common mode (8 wires to ground): 6 kV (1.2/50 us, 42 ohms), criterion B | |
| Relationship between PoE and system power modules [W] | The AP can be powered by DC or PoE over an Ethernet cable or hybrid cable. The power supply modes do not have priorities and do not support hot backup. |
| Maximum number of physical ports on the entire device | 2.5GE (RJ45) x 1, 100M/1000M/2.5GE auto-sensing |
| 10GE (SFP+) x 1, 1000M/10GE auto-sensing | |
| Either the 2.5GE electrical port or SFP+ optical port can be used for data communication at the same time. If both ports are connected, the optical port is preferentially used for communication. | |
| Long-term operating temperature [°C(°F)] | –10°C to +50°C (14°F to 122°F) (If the altitude is in the range of 1800 m to 5000 m, the temperature decreases by 1°C or 1.8°F every time the altitude increases by 300 m.) |
| Storage temperature [°C(°F)] | –40°C to +70°C (–40°F to +158°F) |
| Long-term operating relative humidity [RH] | 5% RH to 95% RH |
| Long-term operating altitude [m(ft.)] | –60 m to +5000 m (–196.85 ft to +16404.20 ft) |
| Atmospheric pressure [kPa] | 53kPa – 106kPa ETSI 300 019-2-3 |
| Ground | floating ground |
| USB | USB 2.0 |
| BLE | BLE5.2 |
| Radio number | 2 |
| Operating frequency band | 2.4GHz |
| 5GHz | |
| MIMO spatial streams | Radio 0 (2.4 GHz): 4×4 |
| Radio 1 (5 GHz): 4×4 | |
| Wi-Fi standard | 2.4G: 802.11b/g/n/ax |
| 5G: 802.11a/n/ac/ac Wave 2/ax | |
| Radio interface | Built-in Dynamic-Zoom Smart Antennas |
| Antenna gain | 2.4G: |
| 4.5 dBi/chain (peak value) | |
| 2 dBi (combined gain) | |
| 5G: | |
| 5.5 dBi/chain (peak value) | |
| 3 dBi (combined gain) | |
| BLE: 4 dBi | |
| Beamwidth of the built-in antenna [degrees] | Common indoor coverage scenario: omnidirectional coverage |
| Indoor high-density coverage scenario: lobe angle of 120° | |
| Maximum transmit power | 2.4G: 26 dBm (Max) |
| 5G: 26 dBm (Max) | |
| NOTE: | |
| This is the MIMO total radio power, which is the same as: | |
| 2.4G: 20 dBm/chain (Max) | |
| 5G: 20 dBm/chain (Max) | |
| BLE: < 10 dBm | |
| Singal radio transmit power [dBm] | 2.4G: -10 dBm to 20 dBm/chain |
| 5G: -10 dBm to 20 dBm/chain | |
| MTBF [year] | 69.7 year |
| MTTR [hour] | 0.5 hour |
| Frequency stability [ppm] | +/-20 |
| 802.3at power supply description | Wi-Fi: |
| If the USB port is not used or the USB port works at the 2.5 W output power, there is no restriction. | |
| If the USB port works at the 5 W output power, the number of MIMO spatial streams on the 2.4 GHz radio decreases to 2×2. | |
| Wired network port: Either the 2.5GE electrical port or SFP+ optical port can be used for data communication at the same time. If both ports are connected, the optical port is preferentially used for communication. | |
| 802.3af power supply description | Wi-Fi: |
| The number of MIMO spatial streams decreases to 2×2 on the 2.4 GHz frequency band, the maximum combined power is 23 dBm, and the 5 GHz frequency band is unavailable. | |
| Wired network port: | |
| In V200R021C00, the rate of the 2.5GE electrical port is reduced to GE and the SFP+ optical port is unavailable. | |
| In V200R021C10 and later versions, either the 2.5GE electrical port or SFP+ optical port can be used for data communication at the same time. If both ports are connected, the optical port is preferentially used for communication. | |
| Other ports: | |
| The USB port is unavailable. | |
| DC power supply description | Either the 2.5GE electrical port or SFP+ optical port can be used for data communication. If both ports are connected, the optical port is preferentially used for communication. |
Reviews
There are no reviews yet.
There are no reviews yet.