![Icon [all products]](https://www.thunder-link.com/tl-content/uploads/2022/05/Icon-all-products-1.svg "Icon [all products]"){kind=icon}
All products
| Functions and Features | |
| Basic function | The line side of the board provides 10 100G QSFP28 ports and 36 10GE SFP+ ports. The rate of each QSFP28 port is 100 Gbit/s, 50 Gbit/s, or 40 Gbit/s, and the rate of each SFP+ port is 10 Gbit/s or 1 Gbit/s. |
| Reliability and availability | Hot swappable. |
| Restrictions and remarks | 1. A 36*10G interface can work in any of the following modes: 10GE LAN, 10GE WAN, and GE. |
| 2. Starting from port 0, every four adjacent ports form a port group. Each port group supports two working modes: | |
| 10GE mode (default): In this mode, each port in a port group can be configured as a 10GE port. | |
| 10GE/GE mode (which can be configured using the port-mode card-id group-id command in the slot view): In this mode, each port in a port group can be configured as a 10GE/GE port. In each port group, 10GE LAN or 10GE WAN is switched by group. The combination of 10GE LAN and 10GE WAN is not supported. | |
| 3. 10GE WAN interfaces support only the master clock. | |
| 4. SFP+ optical modules are used for 10GE ports, SFP optical modules are used for GE ports, and electrical modules are supported by some ports (18, 21, 24, 27, 30, and 33). | |
| 5. The default rate of an port is 100 Gbit/s. Each port supports 100GE/50GE/40GE/4x25GE/4x10GE. If the port transmission rate of an optical module does not match the default rate, you can run the port split command to switch the transmission rate. | |
| 6. {36, 37}, {38, 39}, {40, 41}, {42, 43}, {44, 45}: every two 100G ports can be bonded into a 200G port through FlexE. 400G bonding is not supported. | |
| 7. A fiber extractor is required to remove or insert an optical fiber. | |
| 8. Before inserting or removing a board using an ejector lever, remove the optical module (2, 5, 8, 11, 14, 17, 20, 23, 26, 29, 32, 35, 37, 39, 41, 43 or 45) close to the ejector lever. | |
| Breakout supported | Yes, supported by 100G ports |
| To enable the breakout function on a port, run the port split command. | |
| Interface rate auto-sensing supported | In 10G mode, GE/10GE auto-sensing is supported. |
| Not supported by 100 Gbps QSFP28 ports. | |
| FlexE supported | Yes |
| Physical ports 36 and 37 can be added to the same group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical ports 38 and 39 can be added to the same group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical ports 40 and 41 can be added to the same group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical ports 42 and 43 can be added to the same group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical port 44 can be added to one group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical port 45 can be added to one group. port-id ranges from 1000 to 3000. A maximum of 10 FlexE clients can be created. | |
| Physical specifications | |
| Dimensions without packaging (H x W x D) [mm(in.)] | 55.4 mm x 433 mm x 523.2 mm |
| (2.18 in. x 17.05 in. x 20.59 in.) | |
| Weight without packaging [kg(lb)] | 13 kg (28.66 lb) |
| Weight with packaging [kg(lb)] | 17.9 kg (39.46 lb) |
| Typical power consumption [W] | 712 W |
Reviews
There are no reviews yet.
There are no reviews yet.