Tech Specs

Specification
Fixed port	Forty-four10/100/1000Base-T ports and four GE combo ports
Extended slot	Provides an extended slot for a stack card
Forwarding performance	72 Mpps
MAC address table	IEEE 802.1d compliance
	16K MAC address entries
	MAC address learning and aging
	Static, dynamic, and blackhole MAC address entries
	Packet filtering based on source MAC addresses
VLAN	4K VLANs
	Guest VLAN and voice VLAN
	VLAN assignment based on MAC addresses, protocols, IP subnets, policies, and ports
	1:1 and N:1 VLAN Mapping
	SuperVLAN(supported by the S5700-SI/S5700-EI/S5700-HI series)
Reliability	RRPP ring topology and RRPP multi-instance
	Smart Link tree topology and Smart Link multi-instance, providing the millisecond-level protection switchover
	SEP
	E-Trunk(supported by the S5700-SI/S5700-EI/S5700-HI series)
	STP, RSTP, and MSTP
	BPDU protection, root protection, and loop protection
MPLS features	Not supported
IP routing	Static routing, ECMP
IPv6 features	Neighbor Discovery (ND)
	Path MTU (PMTU)
	IPv6 ping, IPv6 tracert, and IPv6 Telnet
	ACLs based on the source IPv6 address, destination IPv6 address, Layer 4 ports, or protocol type
	MLD v1/v2 snooping
	6to4 tunnel, ISATAP tunnel, and manually configured tunnel(supported by the S5700-SI/S5700-EI/S5700-HI series)
Multicast	IGMP v1/v2/v3 snooping and IGMP fast leave
	Multicast forwarding in a VLAN and multicast replication between VLANs
	Multicast load balancing among member ports of a trunk
	Controllable multicast
	Port-based multicast traffic statistics
QoS/ACL	Rate limiting on packets sent and received by an interface
	Packet redirection
	Port-based traffic policing and two-rate three-color CAR
	Eight queues on each port
	WRR, DRR, SP, WRR+SP, and DRR+SP queue scheduling algorithms
	Re-marking of the 802.1p priority and DSCP priority
	Packet filtering at Layers 2 through 4, filtering out invalid frames based on the source MAC address, destination MAC address, source IP address, destination IP address, port number, protocol type, and VLAN ID
	Rate limiting in each queue and traffic shaping on ports
Security	User privilege management and password protection
	DoS attack defense, ARP attack defense, and ICMP attack defense
	Binding of the IP address, MAC address, interface, and VLAN
	Port isolation, port security, and sticky MAC
	Blackhole MAC address entries
	Limit on the number of learned MAC addresses
	802.1x authentication and limit on the number of users on an interface
	AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC
	SSH v2.0
	Hypertext Transfer Protocol Secure (HTTPS)
	CPU defense
	Blacklist and whitelist
OAM	Supports
Management and maintenance	Virtual cable test
	Stacking
	MAC Forced Forwarding (MFF)
	Port mirroring and RSPAN (remote port mirroring)
	Remote configuration and maintenance using Telnet
	SNMP v1/v2/v3
	RMON
	Web NMS
	HGMP
	System logs and alarms of different levels
	GVRP
	MUX VLAN
DDR memory	256 MB
Flash memory	32 MB
Mean time between failures (MTBF)	S5700-48TP-SI-AC: 34 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Surge protection: Service port protection	Non-PoE switch: ±2 kV in common mode
Surge protection: Power supply protection	Non-PoE switch: AC: ±6 kV in differential mode; ±6 kV in common mode
Stack port	Two stack ports available on each stack card
Maximum stack bandwidth (bidirectional)	48 Gbit/s
RPS	Not supported
PoE	The PWR series support PoE.
Input AC voltage: Rated input voltage range	100 V AC to 240 V AC, 50/60 Hz
Input AC voltage: Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum system power consumption (100% throughput, 100% PoE loads, full speed of fans)	S5700-48TP-SI-AC: 64 W
Operating temperature	0°C to +50°C
Storage temperature	-40°C to +70°C
Noise under normal temperature (27°C, sound power)	S5700-48TP-SI-AC: 0
Relative humidity	5% RH to 95% RH, noncondensing
Operating altitude	Non-PoE switch: AC: 0 m to 5000 m
EMC	CISPR22 Class A
	CISPR24
	EN55022 Class A
	EN50024
	ETSI EN 300 386 Class A
	CFR 47 FCC Part 15 Class A
	ICES 003 Class A
	AS/NZS CISPR22 Class A
	IEC61000-4-2
	ITU-T K 20
	ITU-T K 44
Environmental standards	RoHS
	REACH
	WEEE
Security	IEC 60950-1
	EN 60950-1/A11/A12
	UL 60950-1
	CSA C22.2 No 60950-1
	AS/NZS 60950.1
Laser safety	IEC60825-1
	IEC60825-2
	EN60825-1
	EN60825-2
Dimensions (W x D x H)	442.0 mm x 420.0 mm x 43.6 mm
Fully loaded	≤ 8.5 kg
Empty loaded	≤ 5 kg

Description

Huawei S5700-48TP-SI-AC switch with 48-ports 1000BASE-T, including 4-ports GE SFP combo

With 1 AC power fixed

With 1 extension slot

Layer 3 Ethernet switch

Forwarding perfomance: 72 Mpps

Switching capacity: 256Gbps

16K MAC address entries

Huawei Quidway S5700 series gigabit enterprise switches is designed for high-bandwidth access and Ethernet aggregation. Huawei Quidway S5700 can be used in various campus network scenarios: access switch, aggregation switch, gigabit access switch in Internet data center, or desktop switch to provide 1000 Mbps access for terminals.

Additional information

Weight	8.5 kg
Dimensions	57.7 × 59.5 × 12.0 cm
PoE Type	Non-PoE
Features	Authorized Partner, Original New Sealed
Port	48+
Rate	GE

Q&A

Q: Does S5700-48TP-SI-AC support stack?

A: Yes, but it is not through the stack card, it is through the GE uplink interface.

V200R001: The last two uplink 1000Base-X optical ports can be used as stack ports.

V200R002 and later versions: The four uplink 1000Base-X optical ports can be used as stack ports.

Q: What is the difference between Huawei 5700 switch and 5300 switch?

A: Huawei S5700 target the enterprise market, S5300 target at telecom market, but most function are the same, the manufacturer did this mostly for marketing reasons as the telecom market most are big customers with better discount.

Q: Can an Electrical Interface of the S5700 Be Connected to an O/E Converter?

A: An optical interface of the S5700 can be connected to an O/E converter.

Q: Does the S5700 Interface Support 100M Optical Modules?

A: Fixed optical interfaces on the S5700-EI, S5700-SI, S5710-LI, and S5700-HI support 100M optical modules, while interfaces on extended front cards do not support 100M optical modules.

Combo optical interfaces and 100/1000Base-X optical interfaces on the S5700-LI and S5700S-LI series switches support 100M optical modules.

The S5710-EI series switches support 100M optical modules only on their combo optical interfaces.

Combo optical interfaces and 100/1000Base-X optical interfaces on the S5720-EI series switches support 100M optical modules.

In the S5720-HI series, only the S5720-32C-HI-24S-AC supports 100M optical modules on their 100/1000Base-X optical interfaces.

The S5720-SI series switches support 100M optical modules only on their combo optical interfaces.

Q: How Do I Know that the S5700’s Fan Operates Normally in Intelligent Mode?

A: The fans can work in the intelligent mode or forcible mode.

In the intelligent mode, the fans start to operate only when the ambient temperature goes higher than a specified value. In V200R003C00 and later versions, you can run the display fan speed-adjust threshold minus command on the switches that use the intelligent heat dissipation mode to view the temperature thresholds for the fans to start and stop running. The set fan speed-adjust threshold minus command can be used to lower these temperature thresholds.

Intelligent heat dissipation：

• S5700-24TP-SI-AC

• S5700-24TP-SI-DC

• S5700-48TP-SI-AC

• S5700-48TP-SI-DC

Q: Does the S5700 Support LRM Optical Modules?

A: The S5700SI supports long reach multimode (LRM) optical modules since V100R006C00SPC800. The S5700EI supports LRM optical modules since V100R006C01.

The S5700-LI (10GE optical ports), S5710-C-LI (10GE optical ports), S5700-HI (10GE optical ports), S5710-EI (10GE optical ports), and S5720-EI (only 10GE optical ports on extended interface cards) support LRM optical modules.

Q: Do 10GE Front Subcards of S5700 Switches Support GE/10GE Auto-Sensing?

A: The 10GE front subcards of the S5700EI do not support GE/10G auto-sensing, and 10GE front subcards of the S5700HI and S5700SI support GE/10G auto-sensing.

Q: Can 4*GE and 4*10GE Front Subcards of the S5700EI and S5700SI Switches Be Used Without an Extended Rear Subcard?

A: When a 4*GE or 4*10GE front subcard is used without an extended rear subcard, only two of the four ports on the subcard can be used:

• 4*GE subcard: Only the first and second ports can be initialized. The ports are displayed as GigabitEthernet */1/1 and GigabitEthernet */1/2 after initialization.

• 4*10GE subcard: Only the first and third ports can be initialized. The ports are displayed as XGigabitEthernet */1/1 and XGigabitEthernet */1/2 after initialization.

Q: Are the Cards of S5700 Hot Swappable?

A: Interface cards on the S5700 series except for the S5700EI and S5700SI are hot swappable.

Q: Why Only Two Optical Interfaces Are Displayed After a Front Card Is Installed on an S5700?

A: The reason is that no extended rear card is installed on the S5700.

An S5700-EI or S5700-SI can provide only two optical interfaces for a front card. If a 4-port front card is installed, an ETPB extended rear card must be installed to provide the other two ports. Otherwise, only two optical interfaces are displayed.

Q: Can the Front Card and Stack Card of the S5700C Be Used Simultaneously?

A: When a 2-port front card is installed, the front card and the stack card can be used simultaneously. If a 4-port front card (ES5D000X4S01, ES5D00G4SA01, or ES5D000G4S01) is installed, an ES5D00ETPB00 extended rear card must be installed.

Q: Are Subcards of the S5700SI and S5700EI Support 10GE Ports?

A: The S5700SI and S5700EI switches use front subcards to provide 10GE ports. The ES5D000X2S00 and ES5D000X4S01 front subcards provide 10GE ports on the S5700SI and S5700EI switches. They use SFP+ optical modules.

The S5700SI and S5700EI switches support the ES5D000X2S00 and ES5D000X4S01 front subcards since V100R005.

• An ES5D000X2S00 front subcard can be used without a rear subcard or together with a rear subcard supported by the switches.

• When an ES5D000X4S01 front subcard is used together with an ES5D00ETPB00 extended rear subcard of which the PCB version is VER.C, all the four ports on the ES5D000X4S01 front subcard can be used. If an ES5D000X4S01 front subcard is used without an ES5D00ETPB00 extended rear subcard or used together with a stack rear subcard, only the first and third ports on the front subcard can be used. The two ports are displayed as XGigabitEthernet */1/1 and XGigabitEthernet */1/2 in command lines.

Q: SW5700 Can GE Optical Ports Use 10GE Optical Modules?

A: The four uplink GE optical ports of the S5720-P-SI and S5720S-P-SI series can use 10GE optical modules, but can only be used for stack connections in this case. GE optical ports of other switch models cannot use 10GE optical modules. 100M optical ports cannot use GE or 10GE optical modules.

Q: Can Thunder-link.com provide MIB for Huawei S5700 switch?

A: Yes, you may contact our sales person

Q: Can I get technical support from Thunder-link.com if we purchase S5700-48TP-SI-AC from you?

A: Yes, Thunder-link.com has experienced technical team on Huawei switches, however, you may need to purchase technical support service from us as by default we only provide one year hardware warranty.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “S5700-48TP-SI-AC”

Your email address will not be published. Required fields are marked *

Your rating *

Your review *

Your Country *

Name *

Email

Solve Captcha* Paint

You have to be logged in to be able to add photos to your review.

Why Thunder-link.com

15 Years Experience

As a global leading professional Huawei network hardware and solution provider, we have delivered Huawei, ZTE, Nokia, CISCO, Fiberhome, etc, equipment to 500+ customer groups in 90+ countries over the past 15 years. Know more

Premium Quality Guaranteed

Strict 3-Level Quality Control procedure: 1st-Level inspection; 2nd-Level In-stock test; 3rd-Level 24-hour pre-delivery test to guarantee premium quality. Know more

Value over price

What we offer to our customers is value rather than price. We enable customers to enjoy the benefit of our reliable delivery products and generate more value to the greatest extent. Know more

Tailored Technical Support

We provide customers with personalized and professional tech support by remote diagnosis, fault-location and troubleshooting. "We are here to help you instantly when you need it."

Flexible Payment

We continuously offer flexible payment methods such as Wire Transfer, Paypal, L/C, Western Union and Alipay, to help customer enjoy a more convenient shopping experience. Know more