Huawei S5700-52C-PWR-SI switch with 48-ports 1000BASE-T, 2 power slots, 1 AC power module equipped, 2 extension slots
in stock 3-5 days lead time
Authorized Partner x
Authorized Partner guaranteed or sourced from officially recognized partner. Chassis and modules come with 1 year warranty.
Original New Sealed x
Original, new and sealed switch; original packaging with seal; won't unpack the product without permission (insert the power module or replace the power supply cable).
Huawei S5700-52C-PWR-SI switch with 48-ports 1000BASE-T
With 2 power slots, 1 AC power module included
With 2 extension slots
Layer 3 Ethernet switch
Forwarding perfomance: 132 Mpps
Switching capacity: 256Gbps
16K MAC address entries
POE switch
Huawei Quidway S5700 series gigabit enterprise switches is designed for high-bandwidth access and Ethernet aggregation. Huawei Quidway S5700 can be used in various campus network scenarios: access switch, aggregation switch, gigabit access switch in Internet data center, or desktop switch to provide 1000 Mbps access for terminals.
Specification | |
Fixed port | Forty-eight 10/100/1000Base-T |
Forwarding performance | 132 Mpps |
Extended slot | Provide two extended slots, one for an uplink subcard and the other for a stack card. |
MAC address table | IEEE 802.1d compliance |
16K MAC address entries | |
MAC address learning and aging | |
Static, dynamic, and blackhole MAC address entries | |
Packet filtering based on source MAC addresses | |
VLAN | 4K VLANs |
Guest VLAN and voice VLAN | |
VLAN assignment based on MAC addresses, protocols, IP subnets, policies, and ports | |
1:1 and N:1 VLAN Mapping | |
SuperVLAN(supported by the S5700-SI/S5700-EI/S5700-HI series) | |
Reliability | RRPP ring topology and RRPP multi-instance |
Smart Link tree topology and Smart Link multi-instance, providing the millisecond-level protection switchover | |
SEP | |
ERPS(G.8032)(supported by the S5700-LI/S5700-SI/S5700-EI/S5700-HI series) | |
STP, RSTP, and MSTP | |
BPDU protection, root protection, and loop protection | |
E-Trunk | |
IP routing | Static routing |
RIPv1, RIPv2 and RIPng,ECMP(supported by the S5700-SI/S5700-EI/S5700-HI series) | |
IPv6 features | Neighbor Discovery (ND) |
Path MTU (PMTU) | |
IPv6 ping, IPv6 tracert, and IPv6 Telnet | |
ACLs based on the source IPv6 address, destination IPv6 address, Layer 4 ports, or protocol type | |
MLD v1/v2 snooping | |
6to4 tunnel, ISATAP tunnel, and manually configured tunnel | |
Multicast | IGMP v1/v2/v3 snooping and IGMP fast leave |
Multicast forwarding in a VLAN and multicast replication between VLANs | |
Multicast load balancing among member ports of a trunk | |
Controllable multicast | |
Port-based multicast traffic statistics | |
QoS/ACL | Rate limiting on packets sent and received by an interface |
Packet redirection | |
Port-based traffic policing and two-rate three-color CAR | |
Eight queues on each port | |
WRR, DRR, SP, WRR+SP, and DRR+SP queue scheduling algorithms | |
Re-marking of the 802.1p priority and DSCP priority | |
Packet filtering at Layers 2 through 4, filtering out invalid frames based on the source MAC address, destination MAC address, source IP address, destination IP address, port number, protocol type, and VLAN ID | |
Rate limiting in each queue and traffic shaping on ports | |
Security | User privilege management and password protection |
DoS attack defense, ARP attack defense, and ICMP attack defense | |
Binding of the IP address, MAC address, interface, and VLAN | |
Port isolation, port security, and sticky MAC | |
Blackhole MAC address entries | |
Limit on the number of learned MAC addresses | |
802.1x authentication and limit on the number of users on an interface | |
AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC | |
SSH v2.0 | |
Hypertext Transfer Protocol Secure (HTTPS) | |
CPU defense | |
Blacklist and whitelist | |
OAM | Supports |
Access Security | DHCP Relay, DHCP Server, DHCP Snooping, DHCP Security |
Management and maintenance | Virtual cable test |
Stacking | |
MAC Forced Forwarding (MFF) | |
Port mirroring and RSPAN (remote port mirroring) | |
Remote configuration and maintenance using Telnet | |
SNMP v1/v2/v3 | |
RMON | |
Web NMS | |
HGMP | |
System logs and alarms of different levels | |
802.3az EEE (supported by the S5700(S)-LI, S5710-EI, S5700-HI and S5710-HI) | |
GVRP | |
MUX VLAN | |
DDR memory | 256 MB |
Flash memory | 32 MB |
Mean time between failures (MTBF) | S5700-52C-PWR-SI: 50.4 years when a 2x10GE card is configured; 68.6 years when a 4xGE front card is configured; 35.58 years when a 4x10GE front card is configured |
Mean time to repair (MTTR) | 2 hours |
Availability | > 0.99999 |
Surge protection: Service port protection | PoE switch: ±1 kV in common mode |
Surge protection: Power supply protection | PoE switch: ±2 kV in differential mode; ±4 kV in common mode |
Stack port | Two stack ports available on each stack card |
Maximum stack bandwidth (bidirectional) | 48 Gbit/s |
RPS | Not support |
PoE | The PWR series support PoE. |
Input DC voltage: Rated input voltage range | -48 V DC to -60 V DC |
Input DC voltage: Maximum voltage range | -36 V DC to -72 V DC |
Input AC voltage: Rated input voltage range | 100 V AC to 240 V AC, 50/60 Hz |
Input AC voltage: Maximum voltage range | 90 V AC to 264 V AC, 47 Hz to 63 Hz |
Maximum system power consumption (100% throughput, 100% PoE loads, full speed of fans) | S5700-52C-PWR-SI: 917 W (system power consumption: 177 W; PoE: 740 W) |
Operating temperature | 0°C to 50°C |
Storage temperature | -40°C to +70°C |
Noise under normal temperature (27°C, sound power) | S5700-52C-PWR-SI: less than 45 dBA |
Relative humidity | 5% RH to 95% RH, noncondensing |
Operating altitude | PoE switch: 0 m to 5000 m |
EMC | CISPR22 Class A |
CISPR24 | |
EN55022 Class A | |
EN50024 | |
ETSI EN 300 386 Class A | |
CFR 47 FCC Part 15 Class A | |
ICES 003 Class A | |
AS/NZS CISPR22 Class A | |
IEC61000-4-2 | |
ITU-T K 20 | |
ITU-T K 44 | |
Environmental standards | RoHS |
REACH | |
WEEE | |
Security | IEC 60950-1 |
EN 60950-1/A11/A12 | |
UL 60950-1 | |
CSA C22.2 No 60950-1 | |
AS/NZS 60950.1 | |
Laser safety | IEC60825-1 |
IEC60825-2 | |
EN60825-1 | |
EN60825-2 | |
Dimensions (W x D x H) | 442.0 mm x 420.0 mm x 43.6 mm |
Fully loaded | ≤ 8.5 kg |
Empty loaded | ≤ 5 kg |
Weight | 8.0 kg |
---|---|
Dimensions | 44.5 × 43.7 × 4.5 cm |
PoE Type |
Non-PoE |
Features | |
Port |
48+ |
Q: What is the difference between S5700-52C-PWR-EI and S5700-52C-PWR-SI?
A:Basically there are two big difference:
1.S5700-52C-PWR-EI is coming without power supply while S5700-52C-PWR-SI by default includes single 500W AC Power.
2.Their software is different, for difference of 5700 EI and SI refer below:
Features | S5700-52C-PWR-SI | S5700-52C-PWR-EI |
IPv4 Routing Protocol | Static route/RIP | Static route/RIP/OSPF/BGP/ISIS |
IPv6 Routing Protocol | Static route/RIPng | Static route/RIPng/OSPFv3/BGP4+/ISIS for IPv6 |
Multicast | IGMP Snooping/MLD Snooping | IGMP Snooping/MLD Snooping/IGMP/MLD/MSDP/PIM(IPv4)/PIM(IPv6) |
Traffic analysis | Not supported | sFlow |
MAC address entries | 16K | 32K |
BFD | Not Support | BFD for OSPF, BFD for IS-IS, BFD for VRRP, and BFD for PIM |
MAC address entries | 16K | 32K |
Q: Do I need to buy power supply for S5700-52C-PWR-SI?
A:It depends, a 500W AC Power supply already included in the S5700-52C-PWR-SI switch, however, by adding another 500W power supply, you will improve the PoE outpout power, with default single power supply, max you can use 24 802.3af 15.4W PoE or 12 802.3at 30W PoE+, by adding another 500W power supply, max you will able to use use 48 802.3af 15.4W PoE or 24 802.3at 30W PoE+.
Q: Does S5700-52C-PWR-SI support DC?
A:No, Huawei POE switch only support AC Power supply.
Q: Does S5700-52C-PWR-SI support 802.3at PoE+?
A:Yes, support 802.3af and 802.3at.
Q: What is the available PoE power configured with different power supplies?
A:
Power Supply 1 | Power Supply 2 | Available PoE Power | Switch | PoE Ports(Fully Usage) |
250W | – | 123.2W | S5700-52C-PWR-SI | 802.3af(15.4W/Port): 8
802.3at(30W/Port): 4 |
500W | – | 369.6W | S5700-52C-PWR-SI | 802.3af(15.4W/Port): 24
802.3at(30W/Port): 12 |
250W | 250W | 246.4W | S5700-52C-PWR-SI | 802.3af(15.4W/Port): 16
802.3at(30W/Port): 8 |
500W | 500W | 369.6W | S5700-52C-PWR-SI | 802.3af(15.4W/Port): 48
802.3at(30W/Port): 24 |
Q: Does S5700-52C-PWR-SI support dual power?
A: Yes,The PoE switch provides two power module slots, each supporting a 500 W or 250 W power module. A single power module provides 369.6 W or 123.2 W PoE power for PDs.
Q: Does S5700-52C-PWR-SI support stack?
A: Yes, you just need to purchase the stack card.
Q: How many slots S5700-52C-PWR-SI support?
A: Provide two extended slots, one for an uplink subcard and the other for a stack card.
Q: Which subcard does S5700-52C-PWR-SI support?
A: It supports below 3 subcards:
ES5D000X2S00, 2 10 Gig SFP+ interface card
ES5D000X4S00, 4 10 Gig SFP+ optical interface card(including 4 10 Gig SFP+ interface card and extend channel card)
ES5D00G4SA00, 4 Gig SFP interface card(including 4 Gig SFP optical interface card and extend channel card)
Q: Can I use 4 port subcards on S5700-52C-PWR-SI together with stack card?
A:Yes, but in that case on 4 port subcard only 2 ports can be used, you can use all the 4 ports when no stack card.
Q: Can Thunder-link.com provide MIB for Huawei S5700 switch?
A: Yes, you may contact our sales person
Q: Can I use compatible SFP/SFP+ module on Huawei S5700 switch?
A:Yes, but the switch may generate alarm, however, it will not affect normal use
Q: What is the difference between Huawei 5700 switch and 5300 switch?
A:Huawei S5700 target the enterprise market, S5300 target at telecom market, but most function are the same, the manufacturer did this mostly for marketing reasons as the telecom market most are big customers with better discount.
Q: Can I get technical support from Thunder-link.com if we purchase S5700-52C-PWR-SI from you?
A: Yes, Thunder-link.com has experienced technical team on Huawei switches, however, you may need to purchase technical support service from us as by default we only provide one year hardware warranty.
As a global leading professional Huawei network hardware and solution provider, we have delivered Huawei, ZTE, Nokia, CISCO, Fiberhome, etc, equipment to 500+ customer groups in 90+ countries over the past 10 years. Know more
Strict 3-Level Quality Control procedure: 1st-Level inspection; 2nd-Level In-stock test; 3rd-Level 24-hour pre-delivery test to guarantee premium quality. Know more
What we offer to our customers is value rather than price. We enable customers to enjoy the benefit of our reliable delivery products and generate more value to the greatest extent. Know more
We provide customers with personalized and professional tech support by remote diagnosis, fault-location and troubleshooting. "We are here to help you instantly when you need it."
We continuously offer flexible payment methods such as Wire Transfer, Paypal, L/C, Western Union and Alipay, to help customer enjoy a more convenient shopping experience. Know more
We provide extensive document resources to guide our customers to targetly solve the problem they may meet. Know more
Our products come with 1-year warranty. Customers can ask for a repair, replacement or refund for a major product failure. Know more
We won't stop to develop rapid and cost effective shipping options, providing the excellent experience to our global customers. Know more
We offer not only network products but also network proposal, mainstream and cost-effective solution to assist customers eliminate the concerns.
Huawei S5700-52C-PWR-SI switch with 48-ports 1000BASE-T, 2 power slots, 1 AC power module equipped, 2 extension slots
(0 reviews) | 0
Reviews
There are no reviews yet.