My Cart

Mini Cart

SSN4SLO1602

SSN4SLO1602

PN: 03052881
100 100 1
RFQ

Huawei OSN8800 8xSTM-16 optical interface board SSN4SLO1602 equipped with 8 S-16.1 15km 2.5G ESFP

- +
Hardware Tested

Hardware Tested x

In order to avoid hardware malfunction, each equipment will be strictly tested before delivery and the test report will be packed inside equipment and delivered together. Learn More

Hardware Compatibility

Hardware Compatibility x

Backed up by our experienced pre-sales support team, and volume documentation, to avoid purchasing incompatible hardware.

Software Compatibility

Software Compatibility x

Software compatibility test between active/standby system board, main control board and service board, mother/sub-card; system commissioning test to prevent all software conflicts.

Overview

8×STM-16 Optical Interface Board(S-16.1,LC)

Apply to Huawei OSN8800 T64 T32 T16 subrack

Supports different types of standard optical interfaces, namely, the I-16, S-16.1, L-16.1, and L-16.2. The characteristics of the optical interfaces comply with ITU-T G.957

Supports SFP pluggable optical module

Supports the detection and query of information about the optical module

Provides the ALS function. The optical interface supports the setting of the on/off state of a laser

Supports the VC-12 services, VC-3 services, VC-4 services, VC-4-4c concatenation services, and VC-4-16c concatenation services

Supports SDH Clock Synchronization

Supports the configuration of the D1–D12, E1, F1, and X1 bytes as transparent transmission bytes or into other unused overheads bytes

Supports the transparent transmission and termination of the path overheads

Supports the setting and query of the J0, J1, and C2 bytes

Supports eight channels of ECC communication. Supports HWECC (default) or IP protocol stacks

Supports the 1.5 Mbit/s DCN

Supports the two-fiber and four-fiber ring MSP

Supports the linear MSP, SNCP, SNCTP

Supports the fiber-shared virtual trail protection

Supports the transoceanic MSP ring.

Supports inloops and outloops at optical interfaces

Supports inloops and outloops on VC-4 paths

Supports the function of automatically releasing service loopbacks after the specified time expires

Supports warm resets and cold resets. The warm reset does not affect services

Supports the query of the manufacturing information of the board

Supports the in-service loading of the FPGA

Supports the upgrade of the board software without affecting services

Supports the PRBS function

Supports the press-to-collect function in fault data collection

 

SSN4SLO1602 is a 8-ports STM-16 optical interface board, can be used in OSN 8800 to receive and transmit STM-16 optical signals. SSN4SLO16(S-16.1,LC) part number is 03052881, model name is SSN4SLO1602. SSN4SLO16(S-16.1,LC) comes with 8 units 15km 1310nm ESFP module, transmission distance is 15km. ESFP module is swappable to perform different transmission distance.

Tech Specs
Front Panel

The number code that follows the board name in the bar code is the feature code of the board. The feature code of the SSN4SLO1602 indicates the type of optical interface.

SSN4SLO1602

Valid slot

OSN 8800 T64 subrack: IU1–IU8, IU11–IU42, and IU45–IU68

OSN 8800 T32 subrack: IU1–IU8, IU12–IU27, and IU29–IU36

OSN 8800 T16 subrack: IU1–IU8, and IU11–IU18

Feature Code
The feature code of the SSN4SLO16(S-16.1,LC) indicates the type of optical interface.
Board Feature Code Type of Optical Interface
SSN4SLO1602 02 S-16.1
Optical interface parameters
Parameter Value
Nominal bit rate 2488320 kbit/s
Line code pattern NRZ
Application code S-16.1
Transmission distance (km) 2 to 15
Type of fiber Single-mode LC
Operating wavelength range (nm) 1260 to 1360
Launched optical power range (dBm) -5 to 0
Receiver sensitivity (dBm) -18
Minimum overload (dBm) 0
Maximum -20 dB spectral width (nm) 1
Minimum extinction ratio (dB) 8.2
Typical power consumption (W) 20.5
Maximum power consumption (W) 21.5
Mechanical Specifications
Dimensions (mm) 25.4 (W) x 220 (D) x 266.7 (H)
Weight (kg) 0.8

 

Q&A

Q: Can I use SSN4SLO1602 on OSN6800 or OSN3800?

A: No, you cannot, only OSN8800 supports SSN4SLO1602, but please kindly note that OSN8800 UPS subrack cannot support SSN4SLO1602 either.

 

Q: Can I use SSN4SLO1602 in OSN8800 master or slave subrack?

A: No, it can be used only in an independent subrack, but not in a master or slave subrack.

 

Q: Why does SSN4SLO1602 cannot support SDH ASON in my OSN8800 T16 subrack?

A: Yes, when it is installed in a T16 subrack, the board does not support SDH ASON.

 

 

Matching Products

Reviews(1)

1 review

5.0

100.0%
5 start 5 1
4 start 4 0
3 start 3 0
2 start 2 0
1 start 1 0
  1. Costa Rica
    Value
    100%
    Just need OSN8800 TDM board for SDH service, it works OK.
Write Your Own Review
You're reviewing:SSN4SLO1602
Your Rating:
Why Thunder-link.com
  •  

  •  

  •  

  •  

  •  

  •  

  •  

  •  

  •