| Front Panel |
 |
| Valid Slot |
OSN 9800 U64 Standard subrack: IU1-IU64
OSN 9800 U64 Enhanced subrack: IU1-IU64
OSN 9800 U32 Standard subrack: IU1-IU32
OSN 9800 U32 Enhanced subrack: IU1-IU32
OSN 9800 U16 subrack: IU1-IU14
OSN 9800 M24 subrack: (IU1, IU13), (IU2, IU14), …… , (IU11, IU23), (IU12, IU24) |
| Initial Version: OSN 9800 U series subracks: V100R003C10; M24 subracks: V100R007C00SPC300 |
| Functions and features (line mode) |
| Basic function |
The signal conversion that the N402P board performs varies depending on the modes of port 1 and port 2. Details are as follows:
When both port 1 and port 2 are set to 100G mode, the board performs mutual conversion between ODUk signals with the total bandwidth not exceeding 200 Gbit/s and two channels of OTU4 signals.
When one port is set to 100G mode and the other port is set to 200G mode, the board performs mutual conversion between ODUk signals with the total bandwidth not exceeding 300 Gbit/s and one OTU4 signal plus one OTUC2 signal.
When both port 1 and port 2 are set to 200G mode, the board performs mutual conversion between ODUk signals with the total bandwidth not exceeding 400 Gbit/s and two channels of OTUC2 signals.
When port 1 is set to 400G mode, the board performs mutual conversion between ODUk signals with the total bandwidth not exceeding 400 Gbit/s and one OTUC4 signal. |
| Cross-connect capabilities |
Supports service grooming with cross-connect boards. The service granularities are the sum of granularities supported by port 1 and port 2.
Port in 100G mode:
80 x ODU0/40 x ODU1/10 x ODU2/10 x ODU2e/2 x ODU3/1 x ODU4/80 x ODUflex.
Port in 200G mode:
160 x ODU0/80 x ODU1/20 x ODU2/20 x ODU2e/4 x ODU3/2 x ODU4/160 x ODUflex.
Port in 400G mode:
320 x ODU0/160 x ODU1/40 x ODU2/40 x ODU2e/8 x ODU3/4 x ODU4/320 x ODUflex. |
| License |
The number of licenses is the sum of licenses required by port 1 and port 2. |
| OTN functions |
The OTN function varies depending on the port mode. |
| Port in 100G mode |
Supports the OTU4 interface on the WDM side.
Supports the OTN frame format and overhead processing defined by ITU-T G.709.
OTU4 layer: supports SM overhead processing.
ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads. |
| Port in 200G mode |
Supports the OTUC2 interface on the WDM side.
OTUC2 layer: supports SM overhead processing.
ODUC2 layer: supports PM overhead processing.
ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads. |
| Port in 400G mode |
Supports the OTUC4 interface on the WDM side.
OTUC4 layer: supports SM overhead processing.
ODUC4 layer: supports PM overhead processing.
ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads. |
| WDM specification |
Supports ITU-T G.694.1-compliant DWDM specifications. |
| Tunable wavelength function |
Support tunable wavelength optical modules that provide for 96 wavelengths tunable in the extended C band with 50 GHz channel spacing. |
| Typical channel spacing |
100G QPSK: 50 GHz Fix
200G QPSK: 75 GHz Flex/100 GHz fix
400G QPSK: 2 x (75 GHz Flex/100 GHz fix)
200G 16QAM: 50 GHz Fix
400G 16QAM: 2 x (50 GHz Fix)
200G 8QAM: 62.5 GHz Flex
400G 8QAM: 2 x (62.5 GHz Flex) |
| Latency measurement |
The board supports latency measurement in the WDM-side optical port direction (upstream direction).
When higher-order ODU4 cross-connections are created on the board, TCM latency measurement is supported for higher-order ODU4 channels. When lower-order ODUk cross-connections are created on the board, PM/TCM latency measurement is supported for higher-order ODU4 channels, and TCM latency measurement is supported for lower-order ODUk channels.
The TNU2N402P board supports PM latency measurement at the ODUC2 layer.
The TNU1N402P board does not support latency measurement at the ODUC2 layer. |
| Protection scheme |
Supports ODUk SNCP.
Supports tributary SNCP protection.
Supports intra-board 1+1 protection (when working with the OLP/DCP/QCP board). |
| Functions and features (rely mode) |
| Basic function |
The N402P board applies to electrical regeneration sites to provide the electrical regeneration function for optical signals using port 1 and port 2. Details are as follows:
When both port 1 and port 2 are set to 100G mode, the board electrically regenerates two channels of OTU4 signals.
When both port 1 and port 2 are set to 200G mode, the board electrically regenerates two channels of OTUC2 signals.
When port 1 is set to 400G mode, the board electrically regenerates one OTUC4 signal. |
| License |
The number of licenses is the sum of licenses required by port 1 and port 2. |
| Supported service rate |
OTU4: OTN service at a rate of 111.81 Gbit/s |
| OTN function |
The OTN function varies depending on the port mode.
Port in 100G mode:
Supports the OTU4 interface on the WDM side.
Supports the OTN frame format and overhead processing defined by ITU-T G.709.
OTU4 layer: supports SM overhead processing.
ODU4 layer: Supports PM and TCM overhead processing and non-intrusive monitoring of PM and TCM overheads
Port in 200G mode:
Supports the OTUC2 interface on the WDM side.
OTUC2 layer: supports SM overhead processing.
ODUC2 layer: supports PM overhead processing.
Port in 400G mode:
Supports the OTUC4 interface on the WDM side.
OTUC4 layer: supports SM overhead processing.
ODUC4 layer: supports PM overhead processing. |
| WDM specification |
Supports ITU-T G.694.1-compliant DWDM specifications. |
| Tunable wavelength function |
Support tunable wavelength optical modules that provide for 96 wavelengths tunable in the extended C band with 50 GHz channel spacing. |
| Typical channel spacing |
100G QPSK: 50 GHz Fix
200G QPSK: 75 GHz Flex/100 GHz fix
400G QPSK: 2 x (75 GHz Flex/100 GHz fix)
200G 16QAM: 50 GHz Fix
400G 16QAM: 2 x (50 GHz Fix)
200G 8QAM: 62.5 GHz Flex
400G 8QAM: 2 x (62.5 GHz Flex) |
| Alarm and performance event monitoring |
Monitors BIP8 bytes (Bursty mode) to help locate line failures.
Monitors parameters such as the bias current, temperature, and optical power of the laser.
Monitors OTN alarms and performance events. |
| 150000ps/nm-Extended C Band-Tunable Wavelength-ePDM-100G QPSK/200G QPSK/200G 16QAM/200G 8QAM/400G QPSK/400G 16QAM/400G 8QAM(SDFEC2, SDFEC, T51) |
| Parameter |
100G Mode |
200G Mode/400G Mode |
| Line modulation format |
100G ePDM-QPSK(SDFEC2) |
200G ePDM-QPSK(SDFEC) |
200G ePDM-16QAM(SDFEC) |
200G ePDM-8QAM(SDFEC) |
| DGD tolerance(ps) |
180 |
90 |
180 |
90 |
| Transmitter parameter specifications at point S |
| Center frequency(THz) |
Extended C band:
191.3 to 196.05 (Fixed grid) |
Extended C band:
191.3 to 196.0 (Fixed grid)
191.3125 to 196.0375 (Flex grid) |
Extended C band:
191.3 to 196.05 (Fixed grid) |
Extended C band:
191.3 to 196.05 (Fixed grid)c
191.30625 to 196.04375 (Flex grid) |
| Maximum mean launched power(dBm) |
0 |
2 |
0 |
0 |
| Minimum mean launched power(dBm) |
-5 |
-3 |
-5 |
-5 |
| Center frequency deviation(GHz) |
±2.5 (Fixed grid) |
±2.5 (Fixed grid)
±1.5 (Flex grid) |
±2.5 (Fixed grid) |
±2.5 (Fixed grid)
±1.5 (Flex grid) |
| Maximum -3 dB spectrum width(nm) |
0.3 |
0.6 |
0.3 |
0.4 |
| Dispersion tolerance (back-to-back) (ps/nm) |
150000 |
40000 |
40000 |
40000 |
| Receiver parameter specifications at point R |
| Receiver type |
PIN |
PIN |
PIN |
PIN |
| Operating wavelength range(nm) |
1529-1568 |
1529-1568 |
1529-1568 |
1529-1568 |
| Receiver sensitivity (FEC enabled)(dBm) |
-16 |
-16 |
-16 |
-16 |
| Minimum receiver overload (FEC enabled)(dBm) |
0 |
0 |
0 |
0 |
| Maximum reflectance(dB) |
-27 |
-27 |
-27 |
-27 |
| Mechanical Specifications |
| Dimensions (H x W x D,mm) |
477.3 (H) x 30.5 (W) x 220.0 mm (D) |
| Weight (kg) |
4.8 |
|
Typical Power Consumption (W) |
Maximum Power Consumptiona (W) |
| When both port 1 and port 2 are set to 200G_8QAM mode or the port 1 is set to 400G_8QAM mode |
270 |
280 |
| When both port 1 and port 2 are set to 200G_QPSK mode or the port 1 is set to 400G_QPSK mode |
270 |
280 |
| When both port 1 and port 2 are set to 200G_16QAM mode or the port 1 is set to 400G_16QAM mode |
235 |
245 |
| When both port 1 and port 2 are set to 100G_QPSK mode |
212 |
222 |
Oliver
Smooth cofiguration experience.
Tihonenko
Belarus
New TNU2N402PT51, no disappointment.