UPS5000-A-600 kVA

Cabling

Routed in and out from the top or bottom

IP rating

IP20 (IP21 can be reached by configuring an IP21 component.)

Dimensions (H x W x D)

2000 mm x 1200 mm x 850 mm

2000 mm x 1400 mm x 850 mm

Communication

Supports dry contacts, RS485 ports, and FE ports. Supports the Simple Network Management Protocol (SNMP).

Weight

676 kg

746 kg

1030 kg

UPS5000-A-400K-FTS

1000 V AC/630 A/3P

1000 V AC/800 A/3P

1000 V AC/630 A/3P

1000 V AC/630 A/3P

UPS5000-A-500K-FTS

1000 V AC/800 A/3P

1000 V AC/1000 A/3P

1000 V AC/800 A/3P

1000 V AC/800 A/3P

UPS5000-A-600K-FTS

1000 V AC/1000 A/3P

1000 V AC/1250 A/3P

1000 V AC/1000 A/3P

1000 V AC/1000 A/3P

Operating temperature

0°C to 40°C

Storage temperature

–40°C to +70°C

Relative humidity

0–95% RH (non-condensing)

Altitude

0–1000 m

When the altitude is higher than 1000 m, the power is derated as described in IEC 62040-3. The upper limit of the altitude is 4000 m.

Safety regulations

CE

EN 62040-1:2013

CB

IEC 62040-1:2013

TUV

EN 62040-1:2013

TLC

YD/T 1095-2018

EMC

Conducted emission

EN/IEC 62040-2, C3

Radiated emission

EN/IEC 62040-2, C3

Low-frequency signal interference

IEC 61000-2-2

ESD immunity

IEC 61000-4-2

Conducted susceptibility

EN 61000-4-6

EN/IEC 62040-2

IEC 61000-4-6

Radiated susceptibility

EN 61000-4-3

EN/IEC 62040-2

IEC 61000-4-3

Electrical fast transient

EN/IEC 62040-2

IEC 61000-4-4

Surge

EN/IEC 62040-2

IEC 61000-4-5

Power magnetic susceptibility

IEC 61000-4-8

Voltage dip and temporary interruption

IEC 61000-4-11

Input system

Three-phase, four-wire, and PE

Rated input voltage

380 V AC/400 V AC/415 V AC (line voltage)

Input voltage range

• 80–280 V AC (phase voltage)
• 30°C < Ambient temperature ≤ 40°C: The UPS supports full load when the voltage range is 198–280 V AC. The load is derated to 35% when the voltage range is 80–198 V AC.
• 0°C ≤ Ambient temperature ≤ 30°C: The UPS supports full load when the voltage range is 187–280 V AC. The load is derated to 35% when the voltage range is 80–187 V AC.

Rated frequency

50/60 Hz

Input frequency range

40–70 Hz

Input power factor

• > 0.99 (full load)
• > 0.98 (half load)

THDi

• THDi < 3% (full linear load)
• THDi < 5% (full non-linear load)

Input system

Three-phase, four-wire, and PE

Rated input voltage

380 V AC/400 V AC/415 V AC (line voltage)

Rated frequency

50/60 Hz

Input frequency range

±6 Hz (adjustable, 0.5–6 Hz, ±2 Hz by default)

Input mode

The mains input and bypass input share a power source or use different power sources.

Number of batteries

12 V batteries (30–44 batteries optional, 40 by default). If there are 40 to 44 batteries, the output power is not derated. If there are 38 or 36 batteries, the output power is derated to 0.9. If there are 34 or 32 batteries, the output power is derated to 0.8. If there are 30 batteries, the output power is derated to 0.75.

Battery management

Intelligent battery management

Cold start

If a mains outage occurs, batteries can start the UPS to supply power to loads.

Battery string sharing

Battery string sharing is supported in a parallel system. No battery string is shared by default.

Charge voltage

• Equalized charge voltage: 2.3–2.4 V/cell, default: 2.35 V/cell (30–42 batteries)
• Equalized charge voltage: 2.3–2.35 V/cell, default: 2.35 V/cell (44 batteries)
• Float charge voltage: 2.23–2.3 V/cell, default: 2.25 V/cell (30–44 batteries)

Output system

Three-phase four-wire, and PE

Voltage

380 V AC/400 V AC/415 V AC±1% (line voltage)

THDv

• THDv ≤ 1% (100% linear load)
• THDv ≤ 4% (100% non-linear load)

Output power factor

0.9

Transfer time

• Uninterruptible transfer: 0 ms

• Interruptible transfer: ≤ 20 ms

Phase difference (three phases)

120 degrees (tolerance: ±2 degrees)

100% unbalanced load voltage imbalance

±3%

Overload capability

Inverter overload capability:

• 105% < Linear load ≤ 110%: transfers to bypass mode after 60 minutes

• 0°C ≤ Ambient temperature ≤ 30°C, 110% < Linear load ≤ 125%: transfers to bypass mode after 10 minutes

  30°C < Ambient temperature ≤ 40°C, 110% < Linear load ≤ 125%: transfers to bypass mode after 3 minutes

• 125% < Linear load ≤ 150%: transfers to bypass mode after 30s
• Linear load > 150% or a short circuit occurs: runs for 200 ms

Voltage display precision

Input voltage, bypass voltage, output voltage, bus voltage, and charge voltage: 1%

Frequency display precision

Input, bypass, and output frequency: 1%

ECO in a parallel system

Supported