![Icon [all products]](https://www.thunder-link.com/tl-content/uploads/2022/05/Icon-all-products-1.svg "Icon [all products]"){kind=icon}
All products
in stock inquire lead time
Description
UPS5000-E-200 kVA
Uses a modular design, which facilitates maintenance and capacity expansion.
Adopts intelligent control.
Power module consists of a rectifier, inverter, and DC/DC converter.
Converts inputs into pure high-quality sine wave outputs by using the high-frequency switching technology.
Tech Specs
| Physical Specifications | UPS5000-E-200K-SM |
| Cabling mode | Cables are routed from the top or bottom. |
| IP rating | IP20 (IP21 available if the IP21 component is used) |
| Dimensions (H x W x D) | 2000 mm x 600 mm x 850 mm |
| Communication | Dry contacts, RS485, and SNMP |
| Weight | 330 kg. A maximum of four power modules can be installed. |
| Operating temperature | 0–40°C |
| Storage temperature | –40°C to +70°C |
| Humidity | 0%–95% RH (non-condensing) |
| Altitude | 0–4000 m |
| When the altitude is higher than 2000 m, the power is derated as described in IEC 62040-3. The upper limit of the altitude is 4000 m. | |
| Input system | Three-phase four-wire + PE. If current is allowed in the PE wire, input without the N wire is supported. |
| Rated input voltage | 380 V AC/400 V AC/415 V AC (line voltage) |
| Input voltage | 80–280 V AC (phase voltage) |
| At 40°C: The UPS works at full load when the voltage is 187–280 V AC and is derated to 40% load when the voltage is 187–80 V AC. | |
| At 30°C: The UPS works at full load when the voltage is 176–280 V AC and is derated to 40% load when the voltage is 176–80 V AC. | |
| Rated frequency | 50 Hz/60 Hz |
| Input frequency | 40–70 Hz |
| Input PF | > 0.99 (full load) |
| > 0.98 (half load) | |
| THDi | THDi ≤ 3% (full linear load) |
| THDi ≤ 5% (full non-linear load) | |
| Overvoltage category | OVC II |
| Input system | Three-phase four-wire + PE |
| Rated input voltage | 380 V AC/400 V AC/415 V AC (line voltage) |
| Rated frequency | 50 Hz/60 Hz |
| Input frequency | ±6 Hz (adjustable, 0.5–6 Hz, ±2 Hz by default) |
| Input mode | The mains input and bypass input share a power source or use different power sources. |
| Overvoltage category | OVC II |
| Battery voltage (lead-acid battery) | 12 V battery: 30–44 batteries. 34 batteries: battery inverter output power is derated to 90%; 32 or 30 batteries: battery inverter output power is derated to 80%. |
| 2 V battery: 180–264 batteries. 204–214 batteries: battery inverter output power is derated to 90%; 180–204 batteries: battery inverter output power is derated to 80%. | |
| The number of batteries in the positive battery string must be the same as that of batteries in the negative battery string. | |
| NOTE: | |
| The default number of batteries is 0. Set this parameter based on site requirements. | |
| When the UPS works in normal mode, if the actual load rate exceeds the threshold that could trigger battery derating, an output overload alarm is generated. | |
| Battery management | Intelligent battery management |
| One-button cold start | In the case of a mains failure, batteries can start the UPS to power loads. |
| Charger output power | Under rated conditions, the maximum charge power of a module is 5 kW. |
| Charger current limit | Maximum 10 A for a module |
| Battery string sharing | Battery string sharing is supported in a parallel system. No battery string is shared by default. |
| Charging voltage (lead-acid battery) | Equalized charge voltage: 2.3–2.4 V/cell, default: 2.35 V/cell (30–42 batteries) |
| Equalized charge voltage: 2.3–2.4 V/cell, default: 2.35 V/cell (44 batteries) | |
| Float charge voltage: 2.23–2.3 V/cell, default: 2.25 V/cell (30–44 batteries) | |
| Redundancy design | The auxiliary power supplies, centralized controllers, and parallel signals use redundancy design. |
| No-load loss | 200K: 2 kW |
| 300K: 2.5 kW | |
| ECO in a parallel system | Supported |
| Power distribution system | TN-C, TN-S, TN-CS, TT |
Reviews (0)
Why Thunder-link.com
Reviews
There are no reviews yet.