![Icon [all products]](https://www.thunder-link.com/tl-content/uploads/2022/05/Icon-all-products-1.svg "Icon [all products]"){kind=icon}
All products
inquire lead time
Description
UPS5000-E-400 kVA
Uses a modular design, which facilitates maintenance and capacity expansion.
Adopts intelligent control.
Power module consists of a rectifier, inverter, and DC/DC converter.
Converts inputs into pure high-quality sine wave outputs by using the high-frequency switching technology.
Tech Specs
| Item | 400 kVA |
| Cabling mode | Routed in and out from the top or bottom |
| IP rating | IP20 (IP21 can be reached by configuring an IP21 component.) |
| Dimensions (H x W x D) | 2000 mm x 1200 mm x 850 mm |
| Communication | Supports dry contacts, RS485 ports, and FE ports. Supports the Simple Network Management Protocol (SNMP). |
| Weight | UPS5000-E-400K-SMS: 640 kg |
| UPS5000-E-400K-FMS: 680 kg | |
| Operating temperature | 0–40°C |
| Storage temperature | –40°C to +70°C |
| Humidity | 0%–95% RH (non-condensing) |
| Altitude | 0–4000 m |
| When the altitude is higher than 2000 m, the power is derated as described in IEC 62040-3. The upper limit of the altitude is 4000 m. | |
| Input system | Three-phase four-wire + PE |
| Rated input voltage | 380 V AC/400 V AC/415 V AC (line voltage) |
| Input voltage | 80–280 V AC (phase voltage) |
| 30°C < Ambient temperature ≤ 40°C: The UPS supports full load when the voltage range is 198–280 V AC. The load is derated to 35% when the voltage range is 80–198 V AC. | |
| 0°C ≤ Ambient temperature ≤ 30°C: The UPS supports full load when the voltage range is 187–280 V AC. The load is derated to 35% when the voltage range is 80–187 V AC. | |
| Rated frequency | 50/60 Hz |
| Input frequency range | 40–70 Hz |
| Input power factor | > 0.99 (full load) |
| > 0.98 (half load) | |
| THDi | THDi < 3% (full linear load) |
| THDi < 5% (full non-linear load) | |
| Overvoltage category | OVC II |
| Input system | Three-phase four-wire + PE |
| Rated input voltage | 380 V AC/400 V AC/415 V AC (line voltage) |
| Rated frequency | 50/60 Hz |
| Input frequency range | ±6 Hz (adjustable, 0.5–6 Hz, ±2 Hz by default) |
| Input mode | The mains input and bypass input share a power source or use different power sources. |
| Overvoltage category | OVC II |
| Battery voltage | 360–528 V DC (12 V batteries, 30–44 batteries, 40 batteries by default). If there are 40–44 batteries, the output power is not derated. If there are 38 or 36 batteries, the output power is derated to 90%. If there are 34 or 32 batteries, the output power is derated to 80%. When there are 30 batteries, the output power is derated to 75%. |
| NOTE: | |
| The default number of batteries is 0. Set this parameter based on site requirements. | |
| When the UPS works in normal mode, if the actual load rate exceeds the threshold that could trigger battery derating, an output overload alarm is generated. | |
| Battery management | Intelligent battery management |
| One-click cold start | If a mains outage occurs, batteries can start the UPS to supply power to loads. |
| Charger output power | Under rated conditions, the charger power of a single power module is 5 kW and the maximum charge current is 10 A. |
| Battery string sharing | Battery string sharing is supported in a parallel system. No battery string is shared by default. |
| Charging voltage | Equalized charge voltage: 2.3–2.4 V/cell, default: 2.35 V/cell (30–42 batteries) |
| Equalized charge voltage: 2.3–2.35 V/cell, default: 2.35 V/cell (44 batteries) | |
| Float charge voltage: 2.23–2.3 V/cell, default: 2.25 V/cell (30–44 batteries) | |
| Output system | Three-phase four-wire + PE |
| Voltage | 380 V AC/400 V AC/415 V AC±1% (line voltage) |
| Frequency | In normal mode, the frequency is synchronous with the bypass input frequency. |
| In battery mode, the frequency is 50 Hz/60 Hz with a tolerance of ±0.05%. | |
| Total harmonic distortion of output voltage (THDv) | THDv ≤ 1% (100% linear load) |
| THDv ≤ 4% (100% non-linear load) | |
| Output power factor | 0.9 |
| Transfer time | Uninterruptible transfer: 0 ms |
| Interruptible transfer: ≤ 20 ms | |
| Output voltage unbalance | Voltage unbalance: ±3%; phase unbalance: ±2° |
| Inverter overload capability | 105% < Linear load ≤ 110%: transfers to bypass mode after 60 min |
| 0°C ≤ Ambient temperature ≤ 30°C, 110% < Linear load ≤ 125%: transfers to bypass mode after 10 min | |
| 30°C < Ambient temperature ≤ 40°C, 110% < Linear load ≤ 125%: transfers to bypass mode after 3 min | |
| 125% < Linear load ≤ 150%: transfers to bypass mode after 30s | |
| Linear load > 150% or a short circuit occurs: runs for 200 ms | |
| Continuous overload interval: The preceding overload time is allowed again only 10 min after the system exits the overload state. | |
| Inverter output short-circuit capability | 400K: 826 A |
| 500K: 1063 A | |
| 600K: 1181 A | |
| Redundancy design | The auxiliary power supplies, centralized controllers, and parallel signals use redundancy design. |
| No-load loss | 4.5 kW |
| ECO in a parallel system | Supported |
| Power distribution system | TN-C, TN-S, TN-CS, TT |
Reviews (0)
Why Thunder-link.com
Reviews
There are no reviews yet.