UPS5000-S-200 kVA
Uses a modular design, which facilitates maintenance and capacity expansion.
Adopts intelligent control. Its power module consists of a rectifier, inverter, and DC/DC converter.
Converts inputs into pure high-quality sine wave outputs by using the high-frequency switching technology.
| Item | UPS5000-S-200K-SM |
| Cabling mode | Cables are routed from the top or bottom. |
| Protection level | IP20 (IP21 requires the configuration of IP21 components.) |
| Dimensions (H x W x D) | 2000 mm x 600 mm x 850 mm |
| Communication | Supports dry contacts, RS485 serial port, and FE port. Supports the Simple Network Management Protocol (SNMP). |
| Weight | 330 kg |
| Operating temperature | 0–40°C |
| Storage temperature | –40°C to +70°C |
| Humidity | 0%–95% RH (non-condensing) |
| Altitude | 0–1000 m |
| When the altitude is greater than 1000 m and less than 4000 m, the rated power should be derated. For details, see the IEC62040-3. | |
| Input system | Three-phase, four-wire, and PE wire. |
| Rated input voltage | 380 V AC, 400 V AC, or 415 V AC (line voltage) |
| Input voltage | 80–280 V AC (phase voltage) |
| At 0–40°C: The UPS supports full load when the voltage is 176–280 V AC. The load bearing capacity is derated to 40% when the voltage is 176–80 V AC. | |
| Rated frequency | 50 Hz/60 Hz |
| Input frequency | 40–70 Hz |
| Input PF | > 0.99 (full load) |
| > 0.98 (half load) | |
| THDi | THDi ≤ 3% (full linear load) |
| THDi < 5% (full non-linear load) | |
| Input system | Three-phase, four-wire, and PE |
| Rated input voltage | 380 V AC, 400 V AC, or 415 V AC (line voltage) |
| Rated frequency | 50 Hz/60 Hz |
| Input frequency range | ±6 Hz (0.5–6 Hz, ±2 Hz by default) |
| Input mode | The mains input and bypass input share a power source or use different power sources. |
| Battery voltage (VRLA battery) | 12 V battery: 30–50 batteries (40 by default). 36–39 batteries, the output power is derated to 90%. 30–35 batteries, the output power is derated to 80%. |
| 2 V battery: 180–300 batteries (240 by default). 216–239 batteries, the output power is derated to 90%. 180–215 batteries, the output power is derated to 80%. | |
| Battery management | Intelligent battery management |
| Cold start | In the case of a mains failure, batteries can start the UPS to power loads. |
| Charger output power | Under rated conditions, the maximum charge power of a module is 15 kW. |
| Charger current limit | Maximum 32 A for a module |
| Battery string sharing | Battery string sharing is supported in a parallel system. No battery string is shared by default. |
| Batteries with no neutral wire | Supported |
| Charge voltage (VRLA battery) | Equalized voltage: 2.3–2.4 V/Cell, default: 2.35 V/Cell. |
| Float charging voltage: 2.23–2.3 V/cell. The default voltage is 2.25 V/cell. | |
| Cell minimum voltage (VRLA battery) | 1.6–1.9 V/cell |
| Output system | Three-phase, four-wire, and PE |
| Voltage (V) | 380 V AC/400 V AC/415 V AC±1% (line voltage) |
| Total harmonic distortion of output voltage (THDv) | THDv ≤ 1% (100% linear load) |
| THDv ≤ 3% (100% non-linear load) | |
| Output PF | 1 |
| Transfer time | 0 ms (uninterruptible transfer) |
| ≤ 20 ms (interruptible transfer) | |
| Output voltage unbalance | Voltage imbalance: ±3% |
| Phase imbalance: 120±1° (balanced load), 120±2° (unbalanced load) | |
| Overload capability | Inverter overload capability: |
| 100% < load ≤ 110%: transfers to bypass mode after 60 min or longer | |
| 110% < load ≤ 125%: transfers to bypass mode after 10 min or longer (tolerance ±0.1 minutes) | |
| 125% < load ≤ 150%: transfers to bypass mode after 1 min or longer | |
| Load > 150% or a short circuit occurs: run for 200 ms | |
| Bypass overload capability: | |
| At 30°C, load ≤ 135%: runs for a long time | |
| At 40°C, load ≤ 125%: runs for a long time | |
| Load > 1000%: 100 ms | |
| Inverter short-circuit output capability | 200K: 573 A |
| 300K: 907 A | |
| Redundancy design | The auxiliary power supplies, centralized controllers, and parallel signals use redundancy design. |
| ECO in a parallel system | Supported |
As a global leading professional Huawei network hardware and solution provider, we have delivered Huawei, ZTE, Nokia, CISCO, Fiberhome, etc, equipment to 500+ customer groups in 90+ countries over the past 15 years. Know more
Strict 3-Level Quality Control procedure: 1st-Level inspection; 2nd-Level In-stock test; 3rd-Level 24-hour pre-delivery test to guarantee premium quality. Know more
What we offer to our customers is value rather than price. We enable customers to enjoy the benefit of our reliable delivery products and generate more value to the greatest extent. Know more
We provide customers with personalized and professional tech support by remote diagnosis, fault-location and troubleshooting. "We are here to help you instantly when you need it."
We continuously offer flexible payment methods such as Wire Transfer, Paypal, L/C, Western Union and Alipay, to help customer enjoy a more convenient shopping experience. Know more
We provide extensive document resources to guide our customers to targetly solve the problem they may meet. Know more
Our products come with 1-year warranty. Customers can ask for a repair, replacement or refund for a major product failure. Know more
We won't stop to develop rapid and cost effective shipping options, providing the excellent experience to our global customers. Know more
We offer not only network products but also network proposal, mainstream and cost-effective solution to assist customers eliminate the concerns.
Quote
Feedback
Contact Us
To Top
![Icon [all products]](https://www.thunder-link.com/tl-content/uploads/2022/05/Icon-all-products-1.svg "Icon [all products]"){kind=icon}
All products
Reviews
There are no reviews yet.
There are no reviews yet.